About FAQ Contact Call (808) 219-0537
KitchenAid cooking

KitchenAid oven repair for wall ovens and ranges

A KitchenAid wall oven rated 7.3 to 9.6 kW at 240 volts needs its own 40-amp circuit. Put it on a 30-amp line meant for smaller models and the element may simply never come on.

Black range set under a vent hood between cream kitchen cabinets

KitchenAid oven trouble sorted by what it usually is

KitchenAid's help library treats a lot of oven complaints as settings or installation issues first. Work down this list before you assume an element or a control board has failed.

Keys do nothing

Control Lock. Hold START, or the lower START on a double oven, for 3 seconds to release it.

Display lit, no heat

Demo mode runs a feature show with the elements off. A Delayed Start also waits silently for its set time.

F9 after a remodel

Usually wiring at the supply or hard-wire connection, such as L2 and N swapped. An electrician checks that.

Gas oven will not light

Igniters need a ground path. A two-prong adapter or extension cord on the range cord can stop ignition.

Bakes hot or cold

Run KitchenAid's biscuit test, then calibrate no more than 10 degrees at a time.

Door locked after cleaning

Self-clean holds the latch until the cavity cools. A power cut mid-clean may need a latch reset.

Display guide

KitchenAid oven messages and what to do next

Some of these look alarming and are not faults at all. Others name a part family and need a diagnosis.

ShowsMeaningFault?First stepIf it stays
CDisplay is in CelsiusNoSwitch to Fahrenheit in the settings; in Celsius it stops at 260Owner's manual for your control
PF, PF id=27, PF id=30Power failureNoPress Cancel, reset the clockCheck the breaker
Blank clockClock hidden on purposeNoHold Clock Set/Start about five secondsControl diagnosis
F9, F9 E0Supply wiring or line noiseOften installationBreaker off one minute, on, watch one minuteElectrician checks the supply
F6Oven control or its wiringYesSame one-minute resetControl and harness test
Oahu kitchens

Why the rating plate matters more on Oahu

Most homes here are not new: 67.8 percent of the island's structures were built between 1940 and 1989. A KitchenAid wall oven going into an older kitchen has to match the circuit behind it, and the oven's voltage and frequency sit on the rating plate on the right mounting rail. That plate also carries the model number we need. Parts for a control or an element often travel from the mainland by ship or air, so reading it right before ordering saves a second wait.

Plate on right rail Circuit matched to kW Wiring checked first Parts ordered once
Gas range beneath a stainless hood with wood cabinets on both sides

KitchenAid oven numbers

40 amp
circuit for 7.3 to 9.6 kW wall ovens
30 amp
circuit at 7.2 kW and below
±30°F
calibration range on most controls
10 sec
power-up delay before keys should be pressed

Sources: KitchenAid product help on wall oven power, F9 codes and oven calibration; ACS housing data

01

Codes and controls

KitchenAid says F9 most often means a wiring error at the supply or at the hard-wire connection, for example L2 and N swapped. If the oven went in within about 3 months, have an electrician check the supply before anyone orders a part.
Yes. Keys pressed during the 10-second delay after power returns can set F9, F9 E0 or PF.
Bake a can of 8 refrigerated biscuits on a shiny low-sided sheet in the middle of the oven, with at least 2 inches of space on every side and no foil anywhere. Use the package temperature, or 25°F lower on a dark sheet. If they brown evenly within the package time, leave the setting alone.
Most controls allow 30°F up or down. Holding the Temp/Time down arrow 5 seconds gives 5°F steps; holding BAKE 5 seconds gives 10°F steps on other models.
The display has been switched to Celsius, shown by a C, and 260 is its top setting in that mode.
02

Heat, calibration and gas

Air can get trapped in the gas line after a reconnection. Light a surface burner to purge it, check the main valve where the pipe comes through the wall or floor, and make sure the cord is in a grounded 120 Volt outlet without an adapter.
Not by itself. It means the oven got too hot during the clean, so the controls lock until it cools. Afterward, cut power for 5 minutes to reset the panel.
Press Cancel/Off to start a latch reset, wait 20 to 30 seconds and try the door, or switch the breaker off for one minute. A latch stuck halfway needs service.
A direct connection to the fused disconnect or breaker box through armored or sheathed copper cable with a ground wire, as a 3 or 4 wire hookup sized to the National Electrical Code.
On some gas and dual fuel models it does, and it comes back on once the door is shut.

KitchenAid oven cold or showing a code?

Talk to a person
(808) 219-0537
Call Now →
Sun through Thu 6am-12am | Fri 6am-3:30pm
Call (808) 219-0537